wear hardness的例句大全

The wear resistance, hardness, and other mechanical properties of the composites with nickel coated SiC were better than those of the composites with bare SiC particles.

而且加入镀镍SiC的复合材料的耐磨性、硬度和拉伸强度等力学性能比加入相同含量的未镀SiC的材料的性能要好；

互联网摘选

The study had been proceeded by means of wear test, hardness test, XRD phase testing, metallographic analysis and scanning electron microscopy ( SEM) analysis and other methods.

采用磨损性能测试、硬度测试、XRD物相检测、金相分析及扫描电镜（SEM）等方法进行研究分析。

互联网摘选

Heat treatment can improve the wear resistance and hardness of the electroless composite plating. The existence of composite particle does not influence the microstructure of the coating.

化学复合镀层的性能受涂镀条件的影响，复合颗粒不影响镀层的微结构。

互联网摘选

Among these physical properties are appearance, wear resistance, hardness or brittleness, residual stress, porosity, thickness, and deposit uniformity.

这些物理性能有外观，抗磨损性，硬度或脆性，残余应力，孔椁率，厚度和沉积层的均匀度。

互联网

The results show that the wear resistance and hardness of coating can be enhanced by Ni based alloy coating added with SiC.

结果表明，添加SiC的镍基合金涂层能够提高熔覆层的耐磨性和硬度。

互联网摘选

The results of wear test, hardness and crystallinity measurement show that the filling materials will lower the crystallinity.

结晶度测试、摩擦学性能测试及硬度测试结果表明：填充材料不同程度降低了复合材料的结晶度，而结晶度的降低表征了材料耐磨性能的提高和减摩性能的降低。

互联网摘选

Characteristics of wear resistance and hardness distribution of subsurface of martensitic steels

马氏体钢耐磨性与亚表层硬度分布的关系

互联网摘选

This material possesses high strength and toughness, its wear resistance being similar to that of ceramics. As a result, these tools show good performance in cutting high hardness materials.

这种刀具材料的耐磨性与陶瓷材料相近，并具有较高的强度和韧性，在切削高硬度材料时表现出良好的性能。

互联网摘选

At the same time, the braking material based on benzoxazine from bisphenol and phenolic resin in the presence of hexamine and Lewis acid have been prepared, and the frictional coefficient, tear and wear propert, impact strength and hardness of this material have been determined.

同时制备了以六次、线酚、中间体为主要树脂基体的制动材料，并测定了制动材料的摩擦磨损性能、冲击强度和硬度。

互联网摘选

Development of CO_2 Gas Shielding Flux Core Wire with High Hardness and Research on Wear Resistant Property

高硬度CO2气保护堆焊药芯焊丝的研制及其耐磨性能研究

互联网摘选

Hardness property and wear resistance of al_2o_ ( 3p)/ Zn-Al composite

Al2O（3P）／Zn－Al复合材料的硬度与耐磨性能

互联网摘选

The Polycrystalline diamond ( PCD) has been applied widely in industrial fields as a new cutting tool material of high hardness and good wear-resistance. This thesis designed a type of PCD groove cutter by means of piston ring groove function.

随着聚晶金刚石（PCD）刀具材料在切削铝合金上的广泛应用，本文根据活塞环槽的性能要求及铝合金的切削特点，确定了PCD槽刀几何角度，设计了PCD环槽成型刀具。

互联网摘选

The grinding burn causes the surface hardness falling off and wear speeding up.

磨削烧伤使表面硬度下降，磨损加剧。

互联网摘选

The results show that hard facing layer have high hardness, anti wear performance and suitability.

结果表明，圆点状堆焊层具有较高的硬度、耐磨性及适用性。

互联网摘选

The most important properties of cutting tools are hardness at high temperature, wear resistance, and impact strength.

切削刀具最重要的性能是在高温下能保持的硬度、耐磨损和冲击韧性。

互联网摘选

The wear mechanism of original WC-Ni cemented carbide during the wear process is abrasive wear with the main characteristics of plastic deformation of Ni binder phase and fall-out of WC grains, and wear resistance depends on the hardness of cemented carbide.

原始WC-Ni硬质合金的磨损以Ni粘结相的塑性变形和WC晶粒脱落为主要特征的磨粒磨损，耐磨性依赖于硬质合金的硬度。

互联网摘选

Wear resistance improves as cutting tool hardness increases.

削刃口耐磨，易磨损。削硬越，耐磨性越。

互联网摘选

Ceramics tile are widely used because they have many good characteristics sue has heat-resistance, abrasion hardness, wear-resistance, acid-proof, low-expansion and low-price.

陶瓷玻化砖具有耐高温、高硬度、耐磨损、耐腐蚀、低膨胀系数、价格便宜等特点，因而其用途非常广泛。

互联网摘选

The coating the wearing surface of andanti-wear layer with high surface hardness and excellent corrosion resistance.

膜层硬度高、耐磨性好,具有较优良的综合性能,解决了表面修复的难题.

互联网摘选

This paper researches law of tool material hardness affecting wear in ultrasonic machining.

通过试验研究了以硬度为主的材料性能对超声加工工具磨损影响的规律.

互联网摘选